編程單個SB8F

在對傳感器盒進行編程之前，請確保有線輸入處于所需配置（開/關）以啟用輸出。按下AUTOSET按鈕并按住3秒鐘，直到READING紅燈開始閃爍，然后松開。紅燈（READING）閃爍表示微處理器正在讀取和存儲全部輸入的狀態。然后紅燈熄滅，真空泵壓力，啟用了輸出。黃燈（STORED）指示啟用輸出。

Before programming the sensor box， make sure that the wired inputs are in the confguration (ON/OFF) desired to enable the output. Press the AUTOSET button and hold it down for  3 seconds until the READING red light starts fashing，真空泵公司， then release it.The  red light (READING) fashing indicates that the microprocessor is reading and storing the state of all the inputs. Then the red light goes off and the output is enabled. Output enabling is indicated by the yellow light (STORED).

SB系列傳感器接線盒

? 用于EOAT上傳感器接線。? 可以轉換PNP和NPN信號。? Is/Os可以是拉電流（PNP）、灌電流（NPN）或干觸點。? 可以串聯多個盒子來控制更多傳感器。? 輸入信號重復LED，便于排除故障（不適用于SB15）。? 提供應變消除裝置和固定至型材的套件。

Connection boxes for series SB sensors? Used for sensor wiring on EOATs.? PNP and NPN signals can be converted.? Is/Os can be current sourcing (PNP)， sinking (NPN) or dry contact

Several boxes can be connected in series to control more sensors

Input signal repetition LED for easy troubleshooting  (not for SB15).

Provided with strain reliefs and kit for fastening to profles.

夾具訂制

AGG可在機械手和模具間提供精i準的中心。

注塑模具內金屬嵌件安放時尤其要注意這一點。

夾具AGG...B 安裝在EOAT上，鋼管 AGG...C 安裝在模具上。

一旦機械手向模具靠近，張家口真空泵，夾具在壓力的作用下逐步向鋼管靠近，

并與之接觸。

AGG21-B 和 AGG30-B 采用的是雙動作安全彈簧，確保在壓縮空

氣 (NC)缺失時設備的正常運行。

AGG19-B 采用的是單動作復位彈簧(NO)。

Gripper for engagement

The AGG is used to provide a precise centering between the robot

and the mould.

This necessary when metal inserts must be p1aced in the

mould， before the p1astic injection.

The gripper AGG…-B is fitted on the EOAT， while the steel bushing

AGG…-C is fitted on the mould.

Once the robot has approached the mould， the gripper is

pressurized， thus it closes and engages the bushing.

AGG21-B and AGG30-B are double-acting with a safety spring to

keep the gripper engaged even without compressed air (NC).

AGG19-B is single-acting with reset spring (NO).

真空泵壓力-吉瑪泰克(在線咨詢)-張家口真空泵由吉瑪泰克自動化工程（常熟）有限公司提供。吉瑪泰克自動化工程（常熟）有限公司是一家從事“機械手前端治具，真空系列，傳感器，機電一體化組件”的公司。自成立以來，我們堅持以“誠信為本，穩健經營”的方針，勇于參與市場的良性競爭，使“吉瑪泰克自動化工程”品牌擁有良好口碑。我們堅持“服務至上，用戶至上”的原則，使吉瑪泰克在氣動工具中贏得了客戶的信任，樹立了良好的企業形象。 特別說明：本信息的圖片和資料僅供參考，歡迎聯系我們索取準確的資料，謝謝！